software

What are the best makeblock and arduino projects that we can do? List 2021

The software platform MBLOCK company Makeblock, is one of the most innovative programming tools for beginners. If you are looking to get inspired with new ideas, then check here which are the best MakeBlock and Arduino projects you can do. 2020 list.

The friendly interface lets you program your MBLOCK robots wirelessly Scratch blocks to source Arduino . Through this language there are many inventions that you can replicate.

All the information on the sensors that the board will receive will be sent via USB cable through firmware, previously downloaded to the program.

List of the best MakeBlock and Arduino projects that you can do yourself from scratch

The advantage of mBlock is that, as you build the instructions for the program, you can see the “real code” that the Arduino board uses. Either for educational purposes or because you simply want to expand your knowledge.

Whatever the reason, here is a list of the best MakeBlock and Arduino projects that you can do yourself from scratch:

Ingenious Traffic Lights with Multiple LEDs

Control two traffic lights conditioned to a car waiting or not. To do this, it is necessary to simulate a crossing with traffic lights where the presence of cars is detected to activate or deactivate the traffic lights.

In this simulation you will use push buttons and the following materials:

  • 6 x 220 Ω resistors
  • 2 x Red LEDs
  • 2 x Yellow LEDs
  • 2 x Green LEDs
  • 2 x Pushbuttons
  • 2 x 10 k resistor (pull down)

Theremin with LDR

Although it is an electronic musical instrument, the Theremin does not need physical contact to make it sound. For this proposal, you need to represent the frequency change of the Theremin using an LDR light sensor . As you bring your hand closer to the sensor, the sound will increase in frequency. By moving it away, it will decrease.

The components that you must have to build this project are:

  • 1 x Piezoelectric
  • 1 x LDR photoresist

Soil moisture sensor

This experiment is very simple to carry out, you just have to feed the sensor with ground (GND) and Vcc. Then the output pin reading will be executed with an analog pin from the Arduino. In this case, you must connect the sensor on the Arduino board to pin A0, through the Dupont Funduino type pins .

Next, we indicate the materials to be used:

  • Arduino Edushield Board
  • Glass of water
  • Humidity sensor

LCD screens

This practical project is to show different characters that teach messages or visual elements with Arduino through a small screen. They are a very simple alternative to use. In addition, they give a very professional and commercial touch.

To replicate this work, these are the required components:

  • 16 x 4 LCD screen
  • Arduino UNO board
  • 2 hoses

Simple button

For this project it is necessary to program a switch and illuminate an LED with Arduino at a certain time. The Pull-Down and Pull-Up resistors are the main elements that will allow the correct operation of this work.

The materials to be used are the following:

  • 1 Arduino UNO board
  • 1 Breadboard
  • 4 Hoses
  • 2 Resistors
  • 1 led diode

Locate colors

The mission of this program is basically to discover the colors where the mBlock character moves to activate the different LEDs on the Arduino board.

To represent this project yourself, you will need:

  • 1 Arduino UNO board
  • 1 Breadboard
  • 4 Hoses
  • 3 Led diode
  • 3 Resistance

Servomotor

The main instruction for this program is to move the servomotor from its original position to a final position at 10 ° angles repeatedly.

All you need are these items:

  • 1 Arduino UNO board
  • 3 Hoses
  • 1 Servomotor

Compass with Servo

In this exercise, the task consists of moving a servo using the keyboard arrows and activating two LEDs at the end of the stroke.

The materials to execute the project are:

  • 1 Arduino UNO board
  • 1 Breadboard
  • 3 Hoses
  • 2 Led diode
  • 2 Resistance
  • 1 Servomotor

Temperature sensor

With this of this practice it is required to level the intensity of 3 LED bulbs using a potentiometer, to observe their values ​​from their position of minimum resistance to maximum resistance.

To meet the project requirements you will need:

  • 1 Arduino UNO
  • 1 Breadboard
  • 7 Hoses
  • 3 LEDs (red, orange and blue)
  • 3 100Ω resistor (brown-black-brown)
  • 1 LM35 temperature sensor

Evening RGB LED

The evening LED is a project in which it is necessary to use an LDR light sensor . Its function is to change the colors of an LED belonging to the RGB range. In other words, it should light up in different colors as it darkens through a range of colors.

For this, you will need the following materials:

  • 1 Arduino UNO
  • 1 Breadboard
  • 7 Hoses
  • 1 common anode RGB LED
  • 1 LDR sensor
  • 1 100Ω resistor (brown-black-brown)
  • 2 220Ω resistor (red-red-brown)
  • 1 10KΩ resistor (brown-black-orange)

Get to know the best Arduino kits and boards to work with MakeBlock and get the most out of it

Every beginning programmer needs a simple resource to get them started developing code. The packages Arduino are a good alternative for those looking to develop their own configurations.

For this reason, we leave you a list of the best Arduino kits and boards to work with MakeBlock and get the most out of it:

Arduino Starter Kit for Beginners K030007

It consists of a base material to review classic concepts of electronics and programming. It is recommended for any type of user with minimal or no programming knowledge. It contains 100 components in total, including an Arduino UNO Rev3 board, a 7-inch LCD screen, a set of sensors, cables, LEDs of different colors, motors and resistors.

ELEGOO ES-EL-KIT-008

A fairly complete resource, with 200 components, among which are: an Arduino Mega 2560 R3 board and an expansion card. It also includes more than 60 types of sensors to develop projects. Such is the case with the 1602 LCD module, which has the ability to teach up to two rows of 16 characters. In addition, it offers a manual in Spanish, which will guide you step by step in the world of Arduino programming.

Smraza S48F

It is a particular option to carry out the largest number of programming projects with Arduino . The Smraza S48F board is an Arduino Mega 2560 R3 compatible tool. It has different motor modules, a 1602 four and seven segment LCD screen, a joystick and a wide variety of sensors .

Freenove Ultimate Starter Kit

It is a considerably cheaper tool, ideal for those who just want to try the product. This article includes an Arduino UNO R3 compatible board, and contains over 200 components to program. Additionally, it provides a guide in English and in PDF format to show you basic notions of electronics and explains the development of 51 projects so that you can replicate it yourself step by step .

KeeYees Basic Starter Kit by Arduino for Beginners

In the last place is another low cost alternative. This is the KeeYees Basic Starter Kit, which comes with an ATmega328P development board, 100% Arduino compatible. The package includes items such as: a micro servor motor, LED lights, LED lights, resistors to work more easily. It also offers you 256 parts of up to 33 different component types and modules. Its lessons are explained in a simple way so you can start programming quickly .

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button